.jpg "Large Still for Essential Oil - Model 2022")
.jpg "Large Still for Essential Oil - Model 2022")
.jpg "Preview: Large Still for Essential Oil - Model 2022")
.jpg "Preview: Large Still for Essential Oil - Model 2022")
.jpg "Large Still for Essential Oil - Model 2022")
.jpg "Large Still for Essential Oil - Model 2022")
Construction of optimized distilleries for more than 17 years
DESTILLIERMEISTER E2-4 Supreme-2022
New model 2022 in a particularly solid design, with internally scaled plant tube, height-adjustable aroma basket and further reduced water consumption compared to the predecessor.
Legal, registration-free stainless steel still for essential oils with a full 4 liters of plant space.
20 ml Essenial Oil within 15 Minutes
With over 4 liters of plant space they have plenty of volume to process even larger amounts of plants or drugs. By raising the aroma basket you can also experiment with smaller amounts, but they should then work with reduced heating power. The steam is produced in an extra boiler under the plant container, so that a contact with boiling water can be excluded. The best thing is: Since the kettle is only 2 liters in volume despite the large plant container, the DESTILLIERMEISTER E2-4 Supreme is also legal in Germany and Austria and may be sold and operated without notification.
Simpel handing:
- Pour 1.8 liters of water into the water / steam boiler,
- Place up to 4 liters of plant pipe and close with tension locks,
- Insert aroma basket,
- fill with up to 4 liters of herbs or drugs - do not compress,
- seal as described below
- fit cover 5. and tighten tension locks 4.1,
- insert distillation bridge 6 in socket 5.1,
- screw the coolant hoses to the cooler,
- switch on the heat source and collect oil and Hydrolat at 6.6,
- distill for a maximum of 15 to a maximum of 20 minutes at a higher power (induction plate 2000 watts).
Construction
-
Water / steam boiler, 2 liters. Approx. 1.8 liters of water are filled.
-
4 tension locks for securely locking the water / steam boiler using 2.1.
-
-
Plant / drug pipe, aproximately 4 liters content.
-
Lid to close the kettle,
-
Plant tube,
-
4 tension locks for closing the plant tube by means of the lid 3.
-
-
Lid with socket for the distillation bridge 4.
-
Socket.
-
-
Distilling bridge with curved counterflow power cooler with a comfortable 90 cm cooling length.
-
Riser pipe,
-
Thermometer socket.
-
Comfortable double tube cooler (outer tube jacket, inner tube core) in counterflow with a comfortable cooling length of 100 cm. The cooling water flow can be adjusted to low current, so that the cooling water can absorb a lot of heat. The waste water at 4.5 can therefore be up to 80 °C hot.
-
Cooling water inlet
-
Hot water drain.
-
Hydrolat spout.
-
-
Laboratory thermometer with silicone stopper, insert in 4.2.
-
Height-adjustable aroma basket for inserting into the steam pipe. Unadjusted, this has a distance of about 3 cm to the ground and a closed storage area in the middle, so that the rising jet of steam does not flow directly through the plant material and blows a tunnel due to the jet effect, which would lead to heavy losses. The steam initially flows radially because of the storage area and then rises due to its own thermals. The plant tube has a height/diameter ratio greater than 1, so that an effective chimney effect favors the drag effect. Those who also want to work with smaller amounts of plant material can adjust the basket to the desired height.
Test-Destillation
Heater: Induktion, power after heat up time (about 4 min) 1500 Watt
Droge: Dried Lavender Blossom
Amount: 400 g
Complete Distillation Time: 30 min
Hydrolat Taking: 2 batches, one per 15 min
- Charge: 500 ml after 15 min, oil yield 20 ml, Hydrolat-ph-value: 3,2
- Charge: 500 ml after further 15 min, oil yield 1 ml, Hydrolat-ph-value: 4,1